>
Fa   |   Ar   |   En
   بهینه‌سازی پارامترهای موثر در فرآیند شکل‌دهی آزاد ورق آهنی با روش انفجار زیرآب  
   
نویسنده نصیری صادق ,صادق یزدی میلاد ,میرزابابای مستوفی توحید ,موسوی محسن ,ضیاءشمامی مجتبی
منبع مكانيك هوافضا - 1401 - دوره : 18 - شماره : 3 - صفحه:87 -108
چکیده    یکی از اهداف پژوهش حاضر، بهینه سازی پارامترهای موثر در فرآیند شکل دهی آزاد ورق تحت بارگذاری انفجاری زیرآب است. در بخش تجربی، جهت بررسی اثر نحوه بارگذاری بر میزان بیشترین خیز دائمی و توزیع ضخامت ورق، از ورق‌های آهنی تحت انفجار ناشی از 12 و 4 گرم خرج انفجاری به ترتیب برای بارگذاری منفرد و بارگذاری مکرر سه مرحله ای استفاده شد. همچنین، به‌منظور بررسی اثر پارامترهای موثر بر فرآیند و بهینه‎سازی آن‌ها، ابتدا از روش کوپل اویلری-لاگرانژی جهت شبیه‌سازی عددی در نرم‌افزار المان محدود آباکوس بهره گرفته شد. سپس، در بخش بهینه‌سازی، پاسخ به‌منظور بررسی تاثیر هم زمان پارامترهای جرم خرج انفجاری در هر مرحله و فاصله استقرار روی بیشترین میزان تغییر شکل و ضخامت ورق، از نرم‌افزار طراحی آزمایش و روش سطح استفاده شد. p-value به‌دست‌آمده برای مدل ارائه‌شده کمتر از 0.05 بود که این حاکی از معنی‌دار بودن مدل با ضریب اطمینان بالای 95% است. نتایج به‌دست‌آمده نشان داد که مدل ارائه‌شده توسط نرم‌افزار برای این آزمایش مناسب بوده و مقادیر به‌دست‌آمده از پیش‌بینی مدل با نتایج تجربی و عددی برای خروجی، مطابقت دارد. همچنین، شرایط بهینه برای کمترین تغییر ضخامت و بیشترین میزان تغیرشکل دائمی ورق ارائه شد.
کلیدواژه انفجار زیرآب، بارگذاری مکرر، شکل‌دهی ورق، شبیه‌سازی عددی، بهینه‌سازی
آدرس دانشگاه جامع امام حسین (ع), دانشکده فنی و مهندسی, ایران, دانشگاه جامع امام حسین (ع), دانشکده فنی و مهندسی, ایران, دانشگاه ایوان‌کی, دانشکده مهندسی مکانیک, ایران, دانشگاه جامع امام حسین (ع), دانشکده فنی و مهندسی, ایران, دانشگاه جامع امام حسین (ع), دانشکده فنی و مهندسی, ایران
پست الکترونیکی mziash@ihu.ac.ir
 
   optimization of effective parameters in free iron sheet forming process by underwater explosion method  
   
Authors nasiri sadegh ,sadegh-yazdi milad ,mirzababaie mostofi tohid ,mousavi mohsen ,ziya-shamami mojtaba
Abstract    one of the objectives of the present study is to optimize the effective parameters in the free sheet forming process under underwater explosive loading. in the experimental part, in order to investigate the effect of loading type on the maximum permanent deflection and thickness distribution of the plate, blasted-loaded plates due to 12 g and 4 g of explosive charge were used for single loading and repeated loading, respectively. also, in order to investigate the effect of effective parameters on the process and optimize them, the coupled eulerian-lagrangian method was firstly used for numerical simulation in abaqus finite element software. then, in the optimization section, in order to investigate the simultaneous effect of explosive charge mass at each stage and the standoff distance on the maximum deformation and thickness of the sheet, design-expert software and response surface methodology were used. the p-value obtained for the proposed model was less than 0.05, which indicates the significance of the model with a reliability of over 95%. the obtained results showed that the model provided by the software is suitable for this experiment and the values obtained from predicting the model are consistent with the experimental and numerical results. also, the optimal conditions for the least change in plate thickness and the highest amount of permanent deflection were presented.
Keywords underwater explosion ,repeated loading ,sheet forming ,numerical simulation ,optimization
 
 

Copyright 2023
Islamic World Science Citation Center
All Rights Reserved