>
Fa   |   Ar   |   En
   اصلاح طراحی سازه‌ای یک ماهواره مکعبی برای سازگاری مودال در پرتاب توسط پرتابگر وگاسی  
   
نویسنده حاجی ‌جعفری محمد ,ولی ‌محمد افشین ,مهدوی مهسا
منبع علوم و فناوري فضايي - 1402 - دوره : 16 - شماره : 4 - صفحه:41 -56
چکیده    در این پژوهش پاسخ دینامیکی یک ماهواره مکعبی 12واحدی (20×20×30 سانتی‌متر) در شرایط پرتاب برای سه پیکربندی بررسی شده است. به‌رغم وجود یک طرح موفق برای این ماهواره، با الزام افزودن یک پایه آداپتور به‌منظور نصب روی یک آداپتور استاندارد، طراحی سازه‌ای ماهواره برای سازگاری مودال با پرتابگر اصلاح گردیده که مبتنی‌بر 3 راهکار: اعمال تغییرات هندسی روی سازه، تغییر گستردگی نقاط برای بهبود قیود اتصال به پرتابگر، و تغییر چیدمانی داخلی اجزای سامانه با رعایت استانداردها و اصول سازگاری و هم‌نشینی بود. براین‌پایه، به‌جز افزودن پایه آداپتور و اندک تغییراتی در صفحات جداکننده، یک تیرک محوری به ماهواره اضافه گردیده که باعث تغییر چیدمانی داخلی از جمله دو نیم شدن تانک سوخت (با کاهش گنجایش 595 سانتی‌مترمکعب) گردیده است. به‌رغم افزایش 370 گرمی جرم کل، بسامدهای طبیعی سامانه بدون نیاز به طراحی مجدد به‌اندازه کافی افزایش یافته و تداخل بسامدی با طیف بسامدی پرتابگر وجود نخواهد داشت.
کلیدواژه تحلیل مودال، اصلاح طراحی، ماهواره مکعبی، سازگاری مودال
آدرس مرکز آموزش عالی فنی و مهندسی بوئین ‌زهرا, ایران, دانشگاه صنعتی مالک ‌اشتر, دانشکده فنی و مهندسی, گروه مهندسی هوافضا, ایران, دانشگاه تهران, دانشکده فنی و مهندسی, گروه مهندسی هوافضا, ایران
پست الکترونیکی mahsamahdavi83.mm@gmail.com
 
   structural design modification of a cubesat regarding modal compatibility for launching by vega c launcher  
   
Authors haji jafari mohammad ,vali mohammad afshin ,mahdavi mahsa
Abstract    in this research, the dynamic response of a u-12 cubesat (20x20x30 cm) is investigated for three configurations during the launch conditions. despite the existence of a successful design for this satellite, adding a mount to install on a standard adapter, the structural design of the satellite has been modified for modal computability with the launcher., which is based on 3 general approaches: to apply geometric changes to the structure, changing the extent of the points to improve the limitations of connecting to the launcher, and rearranging the internal system components regarding the standards and principles of compatibility and proximity. therefore, more than the addition of the adapter mount and a few changes in the separating plates, a spire has been added to the structure, which has caused a change in the internal arrangement, including the halving of the fuel tank (by reducing the capacity of 595 cubic centimeters). despite the increase of 370 grams of total mass, the natural frequencies of the system have been increased enough without the need for redesign and there will be no frequency interference with the frequency spectrum of the launcher.
Keywords modal analysis ,design modification ,cubesat ,modal compatibility
 
 

Copyright 2023
Islamic World Science Citation Center
All Rights Reserved