|
|
تولید سیلیکای بیشکل از شلتوک برنج شمال به روش آمایش حرارتی و مقایسه عملکرد آن با سیلیکای تجاری در آمیزه لاستیکی بلت تایر رادیال سواری
|
|
|
|
|
نویسنده
|
شیوا مهدی ,گل محمدی مرتضی ,ضیاتبار علی
|
منبع
|
پژوهش هاي كاربردي مهندسي شيمي - پليمر - 1399 - دوره : 4 - شماره : 3 - صفحه:69 -80
|
|
|
چکیده
|
شلتوک پوشش بیرونی دانه برنج و محصول جانبی فرایند آسیاب برنج است. در این پژوهش استحصال سیلیکای بیشکل از این دورریز کشاورزی به روش آمایش حرارتی و اسیدی/حرارتی مورد مطالعه تجربی قرار گرفت. فرایند کلی به این صورت بود که بعد از سوزاندن شلتوک در فضای آزاد، خاکسترحاصل، اسید شویی و در ادامه خشک شد. در نهایت سیلیکای بی شکل با قرار دادن پودر بهدست آمده در یک کوره الکتریکی استحصال شد (آمایش اسیدی/حرارتی). همچنین یک نمونه دیگر از سیلیکا با حذف مرحله اسیدشویی تولید شد (آمایش حرارتی). سپس، سیلیکاهای بهدست آمده پس از مشخصهیابی در یک فرمول معمول بلت سیمی تایر به جای سیلیکای رسوبی تجاری استفاده و همه خواص فیزیکیمکانیکی از جمله نیروی چسبندگی لاستیک به سیم در دو شرایط معمولی و زمان مندی مطالعه شد. آزمون xrd بر روی دو نمونه نشان داد سیلیکای تولید شده در هر دو روش دارای ساختاری بیشکل هستند. همچنین بهکمک آزمونxrf مشخص شد که درصد خلوص سیلیکای بیشکل برای نمونه تولیدشده بهروش آمایش اسیدی/حرارتی %98.6 و برای نمونه آمایش حرارتی %93.9 است. همچنین نتایج نشان داد چسبندگی لاستیکبه سیم در شرایط معمولی در حضور نمونههای جدید سیلیکا اندکی افت می کند اما همین خاصیت در شرایط زمانمندی شده برای نمونه جدید سیلیکا بهتر از سیلیکای رسوبی تجاری است. سایر خواص آمیزه لاستیکی در حضور گریدهای جدید سیلیکا تغییر محسوسی نشان نداد. درنتیجه میتوان گفت که شلتوک برنج از پتانسیل بالایی برای تولید سیلیکای مناسب جهت استفاده در آمیزه بلت سیمی تایر برخوردارست.
|
کلیدواژه
|
شلتوک برنج، سیلیکای اَریخت، عملیات اسیدی، عملیات حرارتی، تایر
|
آدرس
|
دانشگاه صنعتی بیرجند, گروه مهندسی شیمی, ایران, دانشگاه صنعتی بیرجند, گروه مهندسی شیمی, ایران, شرکت کویرتایر بیرجند, اداره تحقیقات و تکنولوژی, ایران
|
|
|
|
|
|
|
|
|
|
|
Preparation of silica powder from rice husk by thermal treatment and comparison of its performance with commercial silica in blend of passenger radial tire belt
|
|
|
Authors
|
Shiva Mehdi ,Ziatabar Seysd Ali ,golmohammadi morteza
|
Abstract
|
Research subject: The rice husk is the coating on a rice grain and a byproduct of the rice milling process. In this study, the extraction of amorphous silica from this agricultural residue by thermal as well as acid/thermal treatment method was studied.Research approach: The process was designed as follows: after burning the paddy in the open field, the obtained ash was washed with acid followed by drying. Finally, the amorphous silica was obtained by placing the prepared powder in an electric furnace (acid/thermal treatment). Also, a sample of silica was produced by eliminating the acid treatment step (thermal treatment). Afterward, the obtained silica powder was employed in a conventional passenger radial tire belt formula instead of commercial precipitated one, and whole the physicalmechanical properties, including rubbertowire adhesion force, were studied under normal and aging conditions.Main results: The results of the XRD demonstrated that the silica produced in both methods were amorphous. The XRF analysis also showed that the purity of amorphous silica were 98.6% and 93.9% for the sample produced by acid/heat treatment and the heat treatment, respectively. The results of the tire test showed that the rubbertowire adhesion decreased slightly under normal conditions in the presence of new silica samples, but the same property under the timed conditions for the new silica samples was better than commercial precipitated silica. Other properties of the rubber compound did not change significantly in the presence of new silica grades. As a result, it can be said that rice husk has a potential to produce suitable silica for use in blend of radial tire belt.
|
Keywords
|
Rice husk ,Amorphous silica ,Thermal treatment ,Acid treatment ,Tire
|
|
|
|
|
|
|
|
|
|
|