>
Fa   |   Ar   |   En
   مطالعه ریزساختار و ریزسختی جوش فولاد زنگ نزن 316l جوشکاری شده به روش Tig, A-Tig, Fb-Tig  
   
نویسنده رحیمی نگار ,سعید توحید
منبع نشريه علوم و فناوري جوشكاري ايران - 1398 - دوره : 5 - شماره : 2 - صفحه:39 -50
چکیده    در این تحقیق تغییرات عمق نفوذ و ریزساختار و ریزسختی جوش فولاد زنگ نزن l316 در سه حالت tig، atig و fbtig مطالعه و با یکدیگر مقایسه گردید. پس از انتخاب فلاکس بهینه تاثیر آن بر عمق نفوذ، ریزساختار و میکروسختی جوش فولاد زنگ نزن l316 جوشکاری شده به روش های atig و fbtig بررسی و با نمونه tig مقایسه گردید. مشاهده شد عمق نفوذ و نسبت عمق به عرض در روش fbtig نسبت به دو روش دیگر اندکی بیش تر است. همچنین در روش atig در خط مرکزی جوش وسعت دندریت های هم محور مرکزی نسبت به روش fbtig کاهش یافته است. بررسی میکروسختی این سه نمونه نشان داد که سختی خط مرکزی جوش در atig و fbtig بیش تر ازtig است.
کلیدواژه فولاد زنگ نزن Aisi316 L ، عمق نفوذ، ریزساختار، A-Tig ,Fb-Tig ,میکروسختی
آدرس دانشگاه صنعتی سهند, دانشکده مهندسی مواد, ایران, دانشگاه صنعتی سهند, دانشکده مهندسی مواد, ایران
پست الکترونیکی saeid@sut.ac.ir
 
   Study of Microstracture and Microhardness of Welded Austenic Stainless Steel 316L by TIG, A-TIG and FB-TIG Methods.  
   
Authors Rahimi N. ,Saed T.
Abstract    In this study the effect of activating fluxes on the penetration depth, microstructure and microhardness of AISI316L austenitic stainless steel were evaluated by three TIG process variations (TIG, ATIG and FBTIG) and the results were compared together.. After selecting the optimal flux in the second stage, the effect of that on the penetration depth, microstructure and weld microhardness of welded 316L austenitic stainless steel by A ndash;TIG and FBTIG methods, were evaluated and the results were compared by the sample which was welded by TIG process. At this stage, it was found that the depth and width to depth ratio in FBTIG method is slightly greater than the other two methods. Also in FBTIG method, eqiaxed dendritic zone in the center line of weld is slightly greater than in ATIG method. Study of microhardness of weld in three methods shows that in ATIG and FBTIG methods hardness of center line is more than TIG method.
Keywords 316L austenitic stainless steel ,A-TIG ,FB-TIG ,penetration depth ,microstructure ,microhardness ,A-TIG ,FB-TIG
 
 

Copyright 2023
Islamic World Science Citation Center
All Rights Reserved