|
|
شبیهسازی عددی اثر نیروی محوری بر تغییر شکل جانبی ستون بتنی با غلاف فولادی دوپوسته زیر بار انفجار
|
|
|
|
|
نویسنده
|
ایزدی فرد رمضانعلی ,رهبری رزا
|
منبع
|
علوم و فناوري هاي پدافند نوين - 1398 - دوره : 10 - شماره : 3 - صفحه:211 -219
|
|
|
چکیده
|
با افزایش روزافزون کاربرد ستونهای بتنی با غلاف فولادی دوبل، این مطالعه به بررسی اثر نیروی محوری فشاری بر تغییر شکل جانبی ستون ناشی از موج انفجار با استفاده از شبیهسازی عددی در نرمافزار autodyn پرداخته است. بدین منظور ستون بتنی cfdst با مقطع مربع و سطوح مختلف بار محوری (نسبت بار به ظرفیت محوری ستون از 0 تا 80%) مدلسازی و تحت بارگذاری انفجار 35کیلوگرم tnt قرار گرفتند. تحقیق حاضر نشان میدهد برای سطوح پایین بار محوری تغییر مکان بیشینه و ماندگار و نیز شاخص آسیب ستون ناشی از بار جانبی انفجار، با افزایش بار محوری فشاری کاهش یافته است ولی با افزایش بار فشاری از 0.6 ظرفیت محوری ستون، پارامترهای فوق افزایش مییابند. همچنین با استفاده از ضخامت برابر برای ورقهای فولادی داخلی و خارجی، میتوان به کمترین تغییر شکل و آسیب ستون نسبت به حالتی که پوششها دارای ضخامتهای مختلف هستند رسید.
|
کلیدواژه
|
ستون بتنی با غلاف فولادی، نیروی محوری، بار انفجار، تغییر شکل
|
آدرس
|
دانشگاه بینالمللی امام خمینی (ره), ایران, دانشگاه بینالمللی امام خمینی (ره), ایران
|
|
|
|
|
|
|
|
|
|
|
Numerical Simulation of the Axial Load Effects on Lateral Deformation of Concrete Filled Double Skin Steel Tubular under Blast Loading
|
|
|
Authors
|
Izadifard Ramezan Ali ,Rahbari Roza
|
Abstract
|
According the increasing use of concrete filled doubleskin steel tubular (CFDST), this study investigate the effect of axial compressive force on the lateral deformation caused via blast wave by using numerical simulation by AUTODYN software. For this purpose, CFDST with square section and different levels of axial load (p/pu from 0 to 80%) were modeled and subjected to 35 Kg TNT explosion loading. The current research shows that the residual and maximum displacements as well as columns’ damage index caused by blast load are decreased with increasing axial compressive load for lower values of axial force, but by exceeding the axial force over 0.6 of ultimate capacity, the aforementioned parameters are increased. Compared when using plates of different thickness, the minimum deformation and damage could be achieved by applying steel sheets of the same thickness for external and internal cover.
|
Keywords
|
|
|
|
|
|
|
|
|
|
|
|