>
Fa   |   Ar   |   En
   بررسی خواص مکانیکی مواد مرکب پلیمری ساخته شده به روش پرینت سه بعدی  
   
نویسنده صواب پور عباس ,کدخداپور جواد ,پورکمالی انارکی علی
منبع علوم كاربردي و محاسباتي در مكانيك - 1402 - دوره : 35 - شماره : 4 - صفحه:77 -89
چکیده    ماده مرکب یک جامد غیر یکنواخت است که از دو یا چند ماده مختلف تشکیل شده ‌است که به صورت مکانیکی یا متالورژی به هم پیوند خورده‌اند. این مواد تشکیل دهنده، خواص شیمیایی و فیزیکی کاملاً متفاوتی دارند و برای ساخت ماده‌ای که شبیه به هیچ‌کدام از این مواد نیست با هم ادغام می‌شوند. در مطالعات پیشین، ساخت و بررسی ساختارهای ساندویچ مواد پلیمری با دو ماده با خواص فیزیکی مشابه (دو ماده سخت) انجام شده بود، ولی در این تحقیق، دو پلیمر با خواص فیزیکی کاملا متفاوت با هم ترکیب و یک ساختار ساندویچی جدید ساخته شده است. این مطالعه با هدف بررسی و تلاش برای افزایش عملکرد مکانیکی ساختارهای تک لایه و چند لایه مرکب (ساندویچی) چاپ شده از مواد پلیمری سخت (abs) و نرم (tpu) و مقایسه این نمونه‌ها با تهیه ساختارهای مرکب مختلف از این پلیمرها انجام شده است. روش ساخت مواد پلیمری مورد استفاده از این تحقیق، استفاده از تکنولوژی پرینت سه بعدی (لایه گذاری افزایشی) می‌باشد. نتایج در قالب تست کشش آزمایشگاهی و شبیه‌سازی در محیط نرم‌افزاری آباکوس به دست آمده است. این نتایج حاکی از آن است که با تغییر لایه‌ها و مواد، مقدار کرنش تا شکست نمونه‌های مرکب تا حدود 4 برابر افزایش پیدا کرده است. لازم به ذکر است که ساخت نمونه‌های تست کشش، در این پروژه طبق استاندارد انجمن مواد و آزمون آمریکا انجام شده است.
کلیدواژه خواص مکانیکی، ساختارهای مرکب، پرینت سه بعدی، abs ، tpu
آدرس دانشگاه شهید رجایی, دانشکده مهندسی مکانیک, ایران, دانشگاه شهید رجایی, دانشکده مهندسی مکانیک, ایران, دانشگاه شهید رجایی, دانشکده مهندسی مکانیک, ایران
پست الکترونیکی ali_pourkamali@sru.ac.ir
 
   investigating the mechanical properties of polymer composite materials made by 3d printing method  
   
Authors savabpour abbas ,kadkhodapour javad ,pourkamali anaralki ali
Abstract    a composite structure is a non-uniform solid that consists of two or more different materials with different kinds that are mechanically bonded together. these structures have completely different chemical and physical properties and they merge together to make a substance that is not similar to any of these materials. in previous studies, the construction and investigation of sandwich structures of polymer materials were done with two materials with similar physical properties (two hard materials), but in this research, two polymers with completely different physical properties were combined and a new sandwich structure was made. this study aims to investigate and try to increase the mechanical performance of single-layer and multi-layer composite (sandwich) structures printed from hard (abs) and soft (tpu) polymer materials and comparing these samples by preparing different composite structures from these polymers. the method of making polymer materials used in this research is the use of 3d printing technology (incremental layering). the results have been obtained in the form of laboratory tensile test and simulation in the abaqus software environment. these results indicate that with the change of layers and materials, the amount of strain to failure of the composite samples has increased up to about 4 times. it should be noted that the construction of the tensile test samples in this project was done according to the standard of the american association of materials and testing.
Keywords mechanical properties ,composite materials ,3d printing ,abs ,tpu
 
 

Copyright 2023
Islamic World Science Citation Center
All Rights Reserved