|
|
بررسی تاثیر موقعیت و وضعیت هندسی بازشو درمقاومت کمانشی تیرورقهای سوراخدار با سختکننده دلتا تحت تاثیر نیروی برشی
|
|
|
|
|
نویسنده
|
قوهستانی سلیمان ,شیری مهرداد
|
منبع
|
سازه و فولاد - 1398 - دوره : 18 - شماره : 25 - صفحه:35 -44
|
|
|
چکیده
|
امروزه استفاده از تیرورقها در انواع مختلف سازههای ساختمانی گستره وسیعی را به خود اختصاص داده است. یکی از انواع این تیرورقها، تیرورقهای با سختکننده دلتا میباشد؛ که تحقیقات صورت گرفته حاکی از عملکرد بهتر این نوع تیرورق در ظرفیتهای خمشی و برشی نسبت به سایر تیرورقهای معمولی با مقاطع معادل است. تعبیه سوراخهای جان به منظور ایجاد فضایی برای سرویس، بازدید و یا عبور لولههای بزرگ امری اجتنابناپذیر در تیرورقها میباشد. در این پژوهش با استفاده از نرمافزار ansys v.12 وبا مدلسازی و ایجاد سوراخ در جان تیرورق دلتا و در نظر گرفتن پارامترهای موثر بر مقاومت برشی کمانشی تیرورق دلتای سوراخدار، رفتارهای سازهای آنها بررسی شده و محدوده بهینه ایجاد سوراخ و بهترین شکل سوراخ از میان انواع رایج آن معرفی گردیده است.در این بررسی، بهترین محدوده اجرای سوراخ بین 0.30 الی 0.35 طول تیر و بهینه پارامتر (بدون بعد) ارتفاع موثر (نسبت قطر دایره به فاصله اتصال سختکنندهها در محل برخورد با جان تا بال تحتانی مقطع) در محدوده 0.26 الی 0.27 به دست آمده است. همچنین رابطه مقاومت کمانشی نسبت به تغییر قطر بازشو به صورت خطی بوده و توسط یک رابطه بیان شده است. در بین شکلهای بررسی شده با سطوح بازشو برابر (مربع، دایره و مثلث) بازشو مربعی شکل، دارای مقاومت برشی کمانشی بیشتری نسبت به سایر شکلها میباشد.
|
کلیدواژه
|
تیرورق، سختکننده دلتا، سوراخدار، کمانش برشی
|
آدرس
|
دانشگاه فسا, دانشکده فنی و مهندسی, بخش عمران, ایران, دانشگاه آزاد اسلامی واحد بوشهر, ایران
|
|
|
|
|
|
|
|
|
|
|
Study the effect of opening position on shear buckling strength of perforated steel plate girder with delta stiffeners under shear force
|
|
|
Authors
|
Shiri Mehrdad ,Ghouhestani Soleiman
|
Abstract
|
Nowadays, the use of plate girder in different kinds of structures has been increased. One of these is plate girder with delta stiffener. Investigations have shown that the bending and shearing behavior of plate girder with delta stiffener are better than usual plate girder with uniform sections. Preparing web openings to make space for service, inspection and passing the big pipes is unavoidable in plate girders. In this study, employing ANSYS v.12 software, the modeling of hole in the web of plate girder was done and the effective parameters on shear buckling strength of perforated steel plate girder was considered to study the structural behavior and optimum range for Preparation of web hole and the best form of ordinary kinds of hole. The results show that, the best web performance location is between 0.30 until 0.35 of length, optimum of effective height parameter (ratio of hole diameter to distance of stiffener connection from intersection at web to the bottom flange) is between 0.26 until 0.27, and there is a linear behavior between shear buckling strength versus changes in hole diameter of opening which is presented by an equation. The comparison between different opening shape with equal surface (square, circle and triangle) indicates that the square opening has the priority in buckling shear strength in comparison with other shapes.
|
Keywords
|
Plate Girder ,Delta Stiffener ,Perforated ,Shear Buckling
|
|
|
|
|
|
|
|
|
|
|